Inhaler devices

Key points about inhaler devices

  • For asthma, chronic obstructive lung disease and other breathing problems, there are many different types of inhalers (or 'puffers') that are used to help get the medicine into your airways where it is needed.
  • You can find the one that suits you best, by talking to your healthcare provider or asthma educator.
  • Find out about inhaler devices and how to use them.
blue unaunahi tile generic
Print this page

An inhaler is a device used to deliver medicine to the lungs and airways. It is mainly used to treat or prevent diseases of the airways such as asthma, chronic obstructive pulmonary disease (COPD) or cystic fibrosis. By getting medicine directly to the lungs, smaller doses of medicine are needed and it can start working faster.

What are the different types of inhalers?

The main types of inhaler devices are metered dose inhalers and dry powder inhalers.

Metered dose inhalers  

The metered dose inhaler or MDI is an aerosol inhaler used to deliver a short burst, or puff, of medication. Read more about metered dose inhalers below.

Metered dose inhaler

Image credit: Canva

Dry powder inhalers

Dry powder inhalers are handheld devices that deliver medication to your lungs and airways as you inhale through it. Examples of dry powder inhalers include: 

    • Turbuhaler
    • Accuhaler
    • Handihaler
    • Ellipta inhaler
    • Breezhaler


Read more about these different types of dry powder inhalers below.

Soft mist inhaler

The Respimat device is a soft mist inhaler. Read more about the Respimat device below.

  • Inhaled medicines are an important part of asthma and chronic obstructive pulmonary disease (COPD) care.
  • Because inhalers come in many different shapes and sizes, you can find the one that suits you best, by discussing it with your healthcare provider or asthma educator.
  • Not all medicines are available in all the different types of inhaler devices.
  • You may want to try some devices before choosing the one you're most comfortable with.

Things to consider when choosing an inhaler

Metered dose inhaler (MDI) Advantages
  • Widely available for most inhaled medicines.
  • Small, easy to carry (unless used with a spacer).
Disadvantages
  • To get the dose into your lungs requires good technique – you have to coordinate pressing down and breathing in at the same time.
  • Recommended to be used with a spacer.
  • Has a propellant that can sometimes cause throat irritation.
  • Weekly cleaning is recommended to prevent blockages in the device.
Dry powder inhalers  Advantages
  • Doesn't contain a propellant.
  • Doesn't require coordination of breathing in and pressing down.
Disadvantages
  • Not suitable for young children.
  • Not recommended for people who can't breathe in strongly enough to inhale the powder.
Inhalation powder in a hard capsule used in an inhaler 

Advantages
  • Small and easy to carry around.
  • Doesn't contain a propellant.
  • Doesn't require coordination of breathing in and pressing down.
Disadvantages
  • Each dose needs to be loaded immediately before use.
  • Requires deep inhalation (breathing in) to receive the full dose from the capsule.
  • Requires a second breath to ensure the full dose from the capsule has been inhaled.
Soft mist inhalers  Advantages
  • Small and easy to carry around.
  • Doesn't need as much co-ordination of breathing in and releasing the dose as an MDI.
  • Doesn't require a spacer.
  • More medicine reaches your lungs compared with an MDI.
Disadvantages
  • Every new inhaler must be loaded with a new medicine cartridge.
  • It does need some strength and coordination to assemble the inhaler.  

If the inhaler devices are unsuitable, your doctor may recommend the use of a nebuliser. Read more about nebulisers.

  • To get the most benefit from the medicine, it's important to use the correct technique when using your inhaler. This is so you get the right amount of medicine and that it reaches deep inside your lungs.
  • Ask your healthcare provider to show you how to use your inhaler device.
  • Even if you've had asthma or COPD for a long time and have used the same inhaler for years, it's still worth reminding yourself regularly how they work.

Metered dose inhalers are also called MDIs or aerosol inhalers.

  • The medicine is in a small canister, inside a plastic case.
  • When the inhaler is pressed, a measured dose of medicine comes through the mouthpiece.
  • Exactly the same dose is released each time.
  • MDIs require good technique and coordination by pressing down on the inhaler and breathing in at the same time.
  • Because using the inhaler correctly can be difficult, spacer devices are recommended for use with MDIs. The spacer is attached to the MDI to make it easier to use the inhaler and get more medicine into your lungs.
  • MDIs contain different medicines including preventers, relievers, symptom controllers and combinations of medications. Read more about asthma medicines in adultsasthma medicines in children and medications for COPD. 

Video: Using your metered-dose inhaler (puffer)

(National Asthma Council, Australia, 2014)

 How to use your MDI (puffer)

Take off the cap and hold the inhaler upright.
Shake the inhaler to mix the medication.
  Sit upright, tilt your head back slightly (as if you are sniffing) and breathe out gently.

Hold the device upright, insert the inhaler into your mouth, ensuring that your lips firmly seal the mouthpiece.


At the beginning of a slow, deep breath, breathe in through the mouthpiece as you press the inhaler to release one dose or 'puff'.

Breathe in fully, remove the inhaler from your mouth and hold your breath for 10 seconds or as long as is comfortable.
Breathe out gently through your nose.


Using a spacer

A spacer is an attachment to use with your MDI. Using a spacer with your MDI makes it easier to use the inhaler and helps to get the medicine into your lungs, where it’s needed (with less medicine ending up in your mouth and throat). Spacers improve how well your medicine works. Children over 10 years may be able to use an MDI without a spacer; however, babies and young children must use MDIs with a spacer or a spacer and a mask. Read more about spacers.

e-chamber spacer attached to a multidose inhaler

 

Image credit: Healthify He Puna Waiora

Common mistakes when using the MDI

  • Breathing in too fast.
  • Breathing out so hard that you cough.
  • Pressing the puffer too early before you have started to breathe in (if you see a mist of medicine from your mouth, then you're making this mistake).
  • Tilting your head down – it should be tilting back slightly.
  • Pressing the inhaler twice during a single inhalation.
  • Giving the inhaler a 'test puff' into the air and wasting the medication.
  • Breathing in through your nose instead of your mouth.

If you think you might be doing any of these things, ask your healthcare provider to watch you using your inhaler to make sure you're using the right technique.

Cleaning your MDI

Your inhaler can get blocked, especially where the medicine sprays out. Clean your inhaler weekly to make sure it doesn't get blocked.

How to clean it

  • Remove the plastic cap, remove the metal canister (don't put it in water), rinse the plastic case under warm water for at least 30 seconds.
  • Shake off any excess water, and leave the plastic case and cap to dry overnight.
  • Put the metal canister back in, and replace the cap.

Storing your MDI

  • Always keep the cap on your inhaler when it's not in use.
  • Store spare inhalers in cool places (not in your car glove box).
  • Carry a spare clean plastic case so you can change it if the one you're using becomes blocked.

When to start a new inhaler

  • By shaking the inhaler it's possible to hear if there's any medicine left in the canister.
  • Always have a spare inhaler ready, start this before the old one is completely empty.
  • It may help to write the start date on the inhaler, so you can work out how long it will last with daily use. There are usually 200 puffs per canister.

The turbuhaler is a breath-activated device – this means that it will release a dose of medicine when you take a breath in through the mouthpiece.  

  • The turbuhaler delivers the medicine in a dry-powder form. There's no propellant added to the medicine.
  • When you breathe in a dose of the medicine, you will hardly notice any powder in your mouth.
  • Preventers, relievers, symptom controllers and combination medicines are available as turbuhalers.
  • Children from 5 years of age should be able to use a dry powder inhaler.

Examples of medicines available as a turbuhaler

When is a turbuhaler suitable? 

Since the turbuhaler is a breath-activated device, to use the turbuhaler properly, you must be able to breathe in deeply. 

  • Adults and children 5 years of age and older should be able to use the turbuhaler.
  • Some people (eg, those with severe COPD) may not able to breathe in well enough to activate the turbuhaler.

If you don't know if a turbuhaler is the correct device for you, talk to your healthcare provider. 

How to use your turbuhaler

To get the most benefit, it is important to use the correct technique. Ask your healthcare provider to explain how to use your turbuhaler. There's some guidance in the video below.

Video: How to use your turbuhaler device

 

(Healthify He Puna Waiora & Auckland District Health Board, NZ, 2018)

Using your turbuhaler

  • Open: Unscrew and remove the cap. Hold the turbuhaler upright.
  • Load the dose: Twist the base anticlockwise and then back in the other direction until you hear a click. Your turbuhaler is now loaded with 1 dose of medicine
  • Breathe out: Breathe out, away from the turbuhaler. Don't blow directly into the turbuhaler.
  • Inhale your dose: Place the mouth piece in your mouth and form a seal with your lips. Breathe in deeply. Remove the turbuhaler and hold your breath for up to 10 seconds.
  • Close: Replace the cap and twist until it's on properly.
  • Rinse your mouth: Rinse and spit out the water or clean your teeth after using any inhaler that contains a corticosteroid. Ask your healthcare provider if you’re not sure.

Cleaning and storing your turbuhaler

Wipe the mouthpiece with a clean dry tissue. Don't wash the mouthpiece or allow it to get wet when cleaning. Keep the cap on when not in use. The device may get blocked if you breathe out or dribble into it. It can also block up if it's stored in a place where there's high humidity (dampness) with the cap off or unsealed.

When to start a new turbuhaler

There's a window under the mouthpiece on the outside of the turbuhaler called a dose indicator window. When it turns red it is time to get a new turbuhaler. 

Common problems when using a turbuhaler

To get the most benefit, it's important to use the correct technique. Here are a few common problems: 

  • Not holding your turbuhaler upright (vertical) while loading the dose.
  • Covering the air inlets with your lips.
  • Breathing in through your nose instead of your mouth.
  • Shaking the inhaler to see how much is left.
  • Storing your turbuhaler in a damp place with the cap off.

An accuhaler is a breath-activated device – this means that it will release a dose of medicine when you breathe in through the mouthpiece. 

  • Doses of the medicine are preloaded in foil-covered blister packets inside the device. 
  • There are 60 doses in each accuhaler – these can be counted with the dose counter on the device.

Examples of medicines available as an accuhaler

When is an accuhaler suitable?

Since the accuhaler is a breath-activated device, you must be able to breathe in deeply to use it properly. 

  • Adults and children 4 years of age and older should be able to use an accuhaler.
  • Some people (eg, those with severe COPD) may not able to breathe in deeply enough to activate the accuhaler.

If you're not sure if the accuhaler is the correct device for you, talk to your healthcare provider.

How to use your accuhaler

To get the most benefit, it is important to use the correct technique. Ask your doctor, pharmacist, or nurse to explain how to use your accuhaler. There's some guidance in the video below.

Video: How to use an accuhaler inhaler

(Ask the doctor/NHS, UK, 2022)

Using your accuhaler

  • Open: Hold the accuhaler in one hand, and with the thumb of the other hand push the thumb grip away from you until you hear a click. This reveals the mouth piece.
  • Load the dose: Hold the inhaler in a horizontal position. Slide the lever away from you until you hear a click.
  • Breath out: Breathe out, away from the accuhaler. Don't blow directly into your device.
  • Inhale your dose: Place the mouth piece in your mouth and form a seal with your lips. Breathe in deeply and forcefully through your mouth. Remove the accuhaler and hold your breath for up to 10 seconds. If you need another dose, wait for 30 seconds and then repeat the process
  • Close it: Close the inhaler by sliding the thumb grip towards you.
  • Rinse your mouth: Rinse and spit out the water or clean your teeth after using Flixotide and Seretide accuhalers that contain a corticosteroid.

Cleaning and storing your accuhaler

Wipe the mouthpiece with a clean dry tissue. Don't wash the mouthpiece or allow it to get wet when cleaning. Close the device when not in use. 

When to start a new accuhaler

There's a window on the side of the accuhaler called a dose counter. When it turns red it's time to get a new accuhaler.

Common problems when using an accuhaler

To get the most benefit, it's important to use the correct technique. Here are a few common problems:

    • Not loading a dose before using the accuhaler.
    • Not holding the accuhaler horizontally while loading and inhaling the dose. Never hold the inhaler with the mouthpiece pointing down during or after loading a dose; this can cause the medicine to fall out. Keep it horizontal.
    • Not breathing in strongly enough to draw the medicine out of the accuhaler and into your lungs.
    • Not holding your breath long enough after using the accuhaler.
    • Getting moisture inside the accuhaler.
    • Not closing the accuhaler cover after use.

The handihaler is used for the medicine tiotropium (also called Spiriva capsules). Do not swallow the capsules – they must be used by inhaling the contents of the capsule with the handihaler device provided.

  • The handihaler is a breath-activated device – this means it will release a dose of medicine when you inhale on the mouth piece.
  • Tiotropium (Spiriva capsules) is used for people with COPD. Read more about tiotropium.

How to use your HandiHaler

To get the most benefit, it's important to use the correct technique when using your Handihaler. Ask your healthcare provider to show you how to use your Handihaler. The video below provides some guidance.

Video: How to use your Spiriva HandiHaler

 

(Healthify He Puna Waiora & Auckland District Health Board, NZ, 2018)

Using your HandiHaler

  • Open: Press the green button on the side of the handihaler to open the lid. Lift the lid to see the mouthpiece. Pull on the mouthpiece to reveal the capsule chamber.
  • Load the capsule: Spiriva capsules come packaged in blister strips. Peel back the foil from 1 blister strip to release 1 capsule. Don't remove the capsule by pushing it through the foil – this will damage the capsule. Place the capsule into the capsule chamber. Close the mouthpiece firmly until you hear a click.
  • Pierce the capsule: Press the green button on the side to pierce the capsule.
  • Breathe out: Sit upright, tilt your head back (into 'sniff' position) and breathe out gently. Don't breathe into the device.
  • Inhale your dose: Put the mouthpiece into your mouth and seal your lips firmly around it. Breathe in rapidly and deeply through your mouth. You will hear the sound of the capsule vibrating in the chamber. Remove the Handihaler from your mouth and hold your breath for up to 10 seconds.
  • Take 2 breaths from the same capsule: To get your full daily dose, you must take a second breath from the same capsule. You won't need to pierce the capsule again.
  • Discard the used capsule: After inhaling your dose, open the mouthpiece and discard the used capsule. Close the mouthpiece and the lid of the inhaler.  

Cleaning the HandiHaler

  • Clean the device once a month.
  • Open the protective cap, mouthpiece and base.
  • Rinse the whole device with warm water and air-dry thoroughly for 24 hours.
  • Clean the outside of the mouthpiece with a damp tissue when needed.

When to start a new Handihaler

You can use your Handihaler for up to 1 year before replacing. A new one can be prescribed for you or you can buy one from your pharmacy.

Common problems when using the Handihaler

To get the most benefit, it's important to use the correct technique. Here are a few common problems:

  • Piercing the capsule several times or not piercing the capsule at all.
  • Not breathing in strongly enough to draw the medicine out of the inhaler.
  • Not taking a second breath to get the full dose from the capsule.
  • Swallowing the capsule instead of inhaling it through the HandiHaler.
  • Not using a new capsule for each dose.

The Respimat device is a soft mist inhaler. It's a hand-held device in which medicine in a liquid form is converted to a fine mist which is then inhaled.  

  • There's no propellant added to the medicine. It's converted into a fine mist by a compressed spring inside the inhaler.
  • Using the soft mist inhaler needs some coordination as you have to press down slowly and breathe in at the same time.
  • When compared to the metered dose inhaler (MDI) the soft mist inhaler has been shown to leave less medicine in your throat so that more reaches your lungs.

 

Examples of medicines available as a fine mist

How to use your Respimat device 

To get the most benefit, it is important to use the correct technique. Ask your healthcare provider to show you how to use your Respimat device. The video below provides some guidance.

Video: How to use your Respimat device

(Healthify He Puna Waiora & Auckland District Health Board, NZ, 2018)

Preparing your Respimat device

Your Respimat device consists of the device and a cartridge.

Diagram of components of a Spiriva Respimat soft mist inhaler Image credit: Spiriva Respimat CMI


To prepare the device for use, follow the steps below (the numbered points match the numbers on the image):

  • Insert the cartridge: keep the cap closed:
    • 1. Remove the clear base by pressing the safety catch while firmly pulling the base with the other hand
    • 2. Insert the narrow end of the cartridge into the inhaler. Press down on a hard surface (such as a table) to secure the cartridge into the device and close the base.
  • Prime the inhaler: to make sure the device releases the medicine properly, you'll need to prime it:
    • 3. Do this by turning the clear base in the direction of the arrows on the label until it clicks (half a turn). Open the cap, push the release button on the front, until you see the mist come out of the mouth piece. You may need to do this a few times.

Steps for using a Spiriva inhaler

Image credit: Spiriva Respimat CMI & Healthify He Puna Waiora

Inserting the cartridge and priming the Respimat device can be tricky. Ask you pharmacist to load the cartridge for you.

Using your Respimat 

  • Load the dose: Hold the inhaler upright with the cap closed. Turn the base in the direction of arrows until until you hear a click.
  • Breath out: Breathe out, away from the device. Don't blow directly into your device.
  • Inhale your dose: Open the cap and press your lips around the mouthpiece without covering the air vents on either side. Breathe in slowly and deeply through your mouth. Press the dose release button and continue to breathe in.
  • Hold your breath: Hold it for up to 10 seconds. Remove the inhaler from your mouth.
  • Breathe out slowly.

When to start a new device

 There's a counting device on the side of your inhaler, to tell you how many doses are left. When it gets into the red section, it's time to get a new inhaler.

The Ellipta inhaler is a preloaded, breath-activated device – this means that the inhaler has the medicine inside and will release a dose when you inhale through the mouthpiece.  

  • The Ellipta inhaler delivers the medicine in a dry-powder form.
  • There's no propellant added to the medicine.
  • When you breathe in a dose of the medicine, you'll hardly notice any powder in your mouth.

Examples of medicines available as a Ellipta inhaler

How to use your Ellipta inhaler

To get the most benefit, it is important to use the correct technique. Ask your healthcare provider to explain how to use your Ellipta inhaler. The following video provides some guidance.

Video: How to use your Ellipta device

 

(Healthify He Puna Waiora & Auckland District Health Board, NZ, 2018)

Using your Ellipta inhaler

  • Remove the device from the foil packing.
  • Open: pull back the mouth piece cover until you hear a click. Hold the device upright at all times. 
  • Breathe out: Hold the inhaler away from your mouth and breathe out fully.
  • Inhale your dose: press your lips around the mouthpiece without covering the air vents on either side. Begin to breathe in rapidly and deeply through your mouth. Hold your breath for up to 10 seconds. Remove the inhaler from your mouth.
  • Breathe out slowly. Close the mouth piece cover.
  • Rinse your mouth: Rinse and spit out the water or clean your teeth after using Breo Ellipta inhalers that contain a corticosteroid.

Cleaning and storing your Ellipta inhaler

Clean your device once a week by wiping the mouthpiece with a clean dry tissue. Don't wash the mouthpiece or allow it to get wet when you're cleaning it. Close the device when it's not in use. Store it in a cool dry place, away from heat and moisture.

When to start a new inhaler

There's a window on the front of your Ellipta inhaler called a dose counter. When it turns red it's time to get a new inhaler.

The Breezhaler is a breath-activated device – this means it will release a dose of medicine when you inhale through the mouthpiece.

  • The Breezhaler delivers the medicine as a dry-powder. There's no propellant added to the medicine. 
  • When you breathe in a dose of the medicine, you'll hardly notice any powder in your mouth.

Examples of medicines available as a Breezhaler

How to use your Breezhaler device

To get the most benefit, it's important to use the correct technique. Ask your healthcare provider to show you how to use your Breezhaler device. THe video below provides some guidance.

Video: How to use your Breezhaler device

 

(Healthify He Puna Waiora & Auckland District Health Board, NZ, 2018)

Using your Breezhaler device

  • Open: Remove the cover to expose the mouth piece. Pull back the mouthpiece to reveal the capsule chamber.
  • Insert the capsule: The capsules come packaged in a foil wrapping. Pull back the foil edges to release 1 capsule. Don't remove the capsule by pushing it through the foil – this will damage the capsule. Place the capsule into the capsule chamber. Close the mouthpiece until you hear a click.
  • Pierce the capsule: Hold the inhaler upright and press both side buttons at the same time. You should hear a click as the capsule is pierced. Then release the side buttons.
  • Breathe out: Hold the inhaler away from your mouth and breathe out fully.
  • Inhale your dose: Put the mouthpiece into your mouth and seal your lips firmly around it. Breathe in rapidly and deeply until your lungs are full and hold your breath for 10 seconds. You'll hear the sound of the capsule vibrating in the chamber.
  • Take 2 breaths from the same capsule: To get your full daily dose, you must take a second breath from the same capsule.
  • Discard the used capsule: After inhaling your dose, open the mouthpiece and throw away the used capsule. Close the mouthpiece and the lid of the inhaler.

Cleaning and storing your Breezhaler

You can clean your device by wiping the mouthpiece with a clean dry tissue. Don't wash the mouthpiece or allow it to get wet when you're cleaning it. Close the device when it's not in use. Store it in a cool dry place, away from heat and moisture.

When to start a new Breezhaler

Each new pack contains the capsules for inhalation plus a new Breezhaler. Use a new Breezhaler every time you start a new pack of capsules.

Common problems when using a Breezhaler

  • Shaking the inhaler.
  • Not piercing the capsule.
  • Not using a new capsule for each dose.
  • Not breathing in hard enough.

Understanding your inhaler(external link) The Asthma Foundation, NZ
Inhaler identification chart(external link), Asthma and Respiratory Foundation, NZ

References

  1. How to use a Handihaler(external link). Asthma and Respiratory Foundation, NZ
  2. How to use a Respimat(external link). Asthma and Respiratory Foundation, NZ
  3. How to use an Ellipta(external link). Asthma and Respiratory Foundation, NZ
  4. Spiriva capsules(external link) Medsafe Data sheet, NZ

Brochures

Inhaler identification chart

Asthma and Respiratory Foundation, NZ, 2022

Understanding your inhaler

The Asthma Foundation, NZ, 2013

Free helplines

Healthline logo

Text 1737 Helpline logo

Logo with link to Māori Pharmacists website

Credits: Sandra Ponen, Pharmacist, Healthify He Puna Waiora. Healthify is brought to you by Health Navigator Charitable Trust.

Reviewed by: Stephanie Yee, Pharmacist, Healthify He Puna Waiora.

Last reviewed: